| Maximum RPM: Taking the RPM Package Manager to the Limit | ||
|---|---|---|
| Prev | Chapter 2. Using RPM to Install Packages | Next |
Let's have RPM install a package. The only thing necessary is to give the command (rpm -i) followed by the name of the package file:
# rpm -i eject-1.2-2.i386.rpm
#
|
At this point, all the steps outlined above have been performed. The package is now installed. Note that the file name need not adhere to RPM's file naming convention:
# mv eject-1.2-2.i386.rpm baz.txt
# rpm -i baz.txt
#
|
In this case, we changed the name of the package file eject-1.2-2.i386.rpm to baz.txt and then proceeded to install the package. The result is identical to the previous install, that is, the eject-1.2-2 package successfully installed. The name of the package file, although normally incorporating the package label, is not used by RPM during the installation process. RPM uses the contents of the package file, which means that even if the file was placed on a DOS floppy and the name truncated, the installation would still proceed normally.
If you've surfed the World Wide Web, you've no doubt noticed the way web pages are identified:
http://www.redhat.com/support/docs/rpm/RPM-HOWTO/RPM-HOWTO.html
|
This is called a Uniform Resource Locator, or URL. RPM can also use URLs, although they look a little bit different. Here's one:
ftp://ftp.redhat.com/pub/redhat/code/rpm/rpm-2.3-1.i386.rpm
|
The ftp: signifies that this URL is a File Transfer Protocol URL. As the name implies, this type of URL is used to move files around. The section containing ftp.redhat.com specifies the hostname, or the name of the system where the package file resides.
The remainder of the URL (/pub/redhat/code/rpm/rpm-2.3-1.i386.rpm) specifies the path to the package file, followed by the package file itself.
RPM's use of URLs gives us the ability to install a package located on the other side of the world, with a single command:
# rpm -i ftp://ftp.gnomovision.com/pub/rpms/foobar-1.0-1.i386.rpm
#
|
This command would use anonymous FTP to obtain the foobar version 1.0 package file and install it on your system. Of course, anonymous FTP (no username and password required) is not always available. Therefore, the URL may also contain a username and password preceding the hostname:
ftp://smith:mypass@ftp.gnomovision.com/pub/rpms/foobar-1.0-1.i386.rpm
|
However, entering a password where it can be seen by anyone looking at your screen is a bad idea. So try this format:
ftp://smith@ftp.gnomovision.com/pub/rpms/foobar-1.0-1.i386.rpm
|
RPM will prompt you for your password, and you'll be in business:
# rpm -i ftp://smith@ftp.gnomovision.com/pub/rpms/apmd-2.4-1.i386.rpm
Password for smith@ftp.gnomovision.com: mypass (not echoed)
#
|
On some systems, the FTP daemon doesn't run on the standard port 21. Normally this is done for the sake of enhanced security. Fortunately, there is a way to specify a non-standard port in a URL:
ftp://ftp.gnomovision.com:1024/pub/rpms/foobar-1.0-1.i386.rpm
|
Depending on circumstances, the following message might be rare or very common. While performing an ordinary install, RPM prints a warning message:
# rpm -i cdp-0.33-100.i386.rpm
warning: /etc/cdp-config saved as /etc/cdp-config.rpmorig
#
|
RPM solves this the best way it can. It performs two steps:
It renames the original file to cdp-config.rpmorig.
It installs the new cdp-config file that came with the package.
Continuing our example, if we look in /etc, we see that this is exactly what has happened:
# ls -al /etc/cdp*
-rw-r--r-- 1 root root 119 Jun 23 16:00 /etc/cdp-config
-rw-rw-r-- 1 root root 56 Jun 14 21:44 /etc/cdp-config.rpmorig
#
|